Vendor: Vertigo CNC
Type:
Price:
10.00
Vendor: Vertigo CNC
Type:
Price:
30.00
This wheel cover helps protect the U-groove bearings on the Vertigo CNC from dust. All new Vertigo CNCs come with wheel covers as standard, but if you have an older machine without wheel covers, you can buy them here.
There are two types of wheel covers available, depending on which type of machine you have, and which axis the wheels are on - so make sure you select the right ones above.
Vendor: Vertigo CNC
Type:
Price:
15.00
This cable allows a third-party laser module to be connected to the Vertigo CNC. The cable connects to the a 4-pin Molex connector near the Z-axis of the Vertigo CNC. The other end of the cable is broken out into three wires (+24V, GND, and 3.3V PWM) so that it can be connected to any PWM-controlled 24V laser module.
Please note that if you have an older Vertigo CNC (before mid-2018), your laser connector may look different. If so, please leave us a note in your order to let us know so that we can send you the correct type of cable.
Warning: Installing a third-party laser may require soldering. Please ensure you fully understand your laser's wiring requirements before beginning. Incorrect wiring of your laser may cause damage to the laser or to the Vertigo CNC's control circuitry. Such damage is not covered by our warranty.
Vendor: Vertigo CNC
Type:
Price:
15.00 - 20.00
(2 variants)
These clamps slide into the T-tracks on the bed of the Vertigo CNC and can be placed at various points on the machine. This allows you to securely clamp various different sizes of material.
Each clamp consists of a T-bolt, a washer, and a wingnut.
The Vertigo CNC comes with a selection of clamps, but you can buy additional ones here. The clamps can also be used in other applications that use 3¼ inch T-slot track.
]]>
Vendor: Vertigo CNC
Type:
Price:
5.99
This flexible coupling connects the X and Y motors to their respective lead screws. It can be used as a drop-in replacement for the rigid couplings that were used in older Vertigo CNC machines.
Vendor: Vertigo CNC
Type:
Price:
5.99
This is a replacement foot for the Vertigo CNC.
Comes with two M8 nuts.
]]>
Vendor: Vertigo CNC
Type:
Price:
100.00
This stepper motor provides 1.26 Newton-metres (178.4 ounce-inches) of torque. Its relatively flat torque curve helps the Vertigo CNC cut through relatively tough materials, while still achieving fast "rapids" between cuts, and also keeping feed-rates fast when step-downs are low.
Being a brushless motor, it rarely fails - but if it does, you can easily purchase a replacement here. Also, if you have a Vertigo CNC with the older generation of motors (look for "1504S" in the part number of the back of the motor), you may want to replace them with the latest motors in order to get improved performance from your machine.
For installation, choose either the four-pin Molex connector (for plug-and-play installation on Vertigo CNC machines built after mid-2018) or unterminated wires that can be soldered directly to your custom machine or older Vertigo CNC.
Vendor: Vertigo CNC
Type:
Price:
30.00
This stepper motor provides 1.26 Newton-metres (178.4 ounce-inches) of torque. Its relatively flat torque curve helps the Vertigo CNC cut through tough materials, while still achieving fast "rapids" between cuts, and also keeping feed-rates fast when step-downs are low.
Being a brushless motor, it rarely fails - but if it does, you can easily purchase a replacement here. Also, if you have a Vertigo CNC with the older generation of motors (look for "1504S" in the part number of the back of the motor), you may want to replace them with the latest motors in order to get improved performance from your machine.
This stepper motor is also ideal for various non-CNC applications.
For installation, choose either the four-pin Molex connector (for plug-and-play installation on Vertigo CNC machines built after mid-2018) or unterminated wires that can be soldered directly to your custom machine or older Vertigo CNC.
If you're building a new machine with these motors, you may want to consider also getting our compatible flexible motor couplings.
Vendor: Vertigo CNC
Type:
Price:
1.50
This belt couples the motor to the lead screw on the Z-Axis of the Vertigo CNC.
Sold in closed-loop sections of 154mm.
Vendor: Vertigo CNC
Type:
Price:
5.99
This is a replacement anti-backlash nut for the Vertigo CNC.
Vendor: Vertigo CNC
Type:
Price:
4.99
This polyoxymethylene (Delrin) v-groove wheel sits between the gantry plates and the y-axis rails, on the bottom side of the rail. Each machine has four of these wheels - two on each side.
The replacement kit comes with everything you need, including the wheel cover, bearing, three precision shims, lock nut, M5x30 bolt and eccentric nut.
The wheel is compatible with standard OpenBuilds V-Slot extrusion, and can be used as a direct replacement for the original wheels on machines such as the OpenBuilds ACRO System - which uses the OpenBuilds Solid V Wheel Kit - but at a fraction of the price!
Vendor: Vertigo Technologies
Type:
Price:
500.00
Vertigo Tech is now offering an affordable two-day training course that will teach you everything you need to know to go from an idea to a finished product using a desktop CNC. The classes are hands-on, and you’ll get to take away your finished work at the end.
Courses are currently available in Auckland, Wellington and Christchurch. To keep class sizes small, spaces are limited to 8 attendees per class - so get in quick!
The course will cover the following topics:
You’ll learn useful tips and tricks, and you’ll get a full set of course notes to take away with you for future reference. You’ll get to use the Vertigo desktop CNC router at the course, but the skills you learn will be applicable to any CNC machine.
The course is run by Vertigo Technologies’ CEO Brett Cottle, who created the Vertigo CNC and also operates full-size CNC milling machines.
Vendor: Vertigo Technologies
Type:
Price:
114.95
FLAT EMU 6D 0.25SHK 2F 20FL 20LBS 58OAL
FLAT EMD 6D 0.25SHK 2F 12FL 26LBS 58OAL
BALL 6D 0.25SHK 2F 16FL 16LBS 58OAL
FLAT EMU 3D 0.25SHK 2F 8FL 8LBS 58OAL
CHAMFER 0.25D 0.25SHK 2F 0.125FL 0.125LBS 58OAL 90DEG
Vendor: ChipX
Type: Router Bit
Price:
31.63
The ChipX EMU06-025-3F-2550-80 up-cut end mill is specially designed for desktop CNC routers such as the Vertigo machines. It provides great cutting performance in both low and high-density foams.
Product Data
|
|
Cutter Type | Up-cut End Mill |
Coating | None |
Coolant | None |
Corner Radius | 0in (0mm) |
Overall Length | 80mm |
Unit System | mm |
Shank Diameter | 0.25in (6.35mm) |
Diameter | 6mm |
Flutes | 3 |
Flute Length | 25mm |
Length Below Shank | 50mm |
Helix Angle | 15 Degrees |
Vendor: ChipX
Type: Router Bit
Price:
22.77
The ChipX EMU06-025-2F-2020-58 up-cut end mill is specially designed for desktop CNC routers such as the Vertigo machines. It provides great cutting performance in a variety of materials such as timber, ply, MDF, plastics, and can even be used on aluminium. The 1/4″ shank size allows you to use most trim routers without adapters.
Product Data
|
|
Cutter Type | Up-cut End Mill |
Coating | None |
Coolant | None |
Corner Radius | 0in (0mm) |
Overall Length | 58mm |
Unit System | mm |
Shank Diameter | 0.25in (6.35mm) |
Diameter | 6mm |
Flutes | 2 |
Flute Length | 20mm |
Length Below Shank | 0in (0mm) |
Helix Angle | 45 Degrees |
Workpiece Material | ISO N Non-Ferrous Materials |
Vendor: ChipX
Type: Router Bit
Price:
27.60
The ChipX EMU06-025-1F-1616-58 up-cut end mill is specially designed for desktop CNC routers such as the Vertigo machines. It provides great cutting performance in a variety of materials such as timber, ply, MDF, plastics, and can even be used on aluminium. The 1/4″ shank size allows you to use most trim routers without adapters.
Product Data | |
Shank Diameter | 0.25in (6.35mm) |
Brand | ChipX |
Coating | None |
Coolant | None |
Corner Radius | 0in (0mm) |
Cutter Type | Up-cut End Mill |
Diameter | 6mm |
Flute Length | 16mm |
Flutes | 1 |
Overall Length | 58mm |
Length Below Shank | 0in (0mm) |
Unit System | mm |
Workpiece Material | ISO N Non-Ferrous Materials |
Helix Angle | 45 Degrees |
Vendor: ChipX
Type: Router Bit
Price:
22.77
The ChipX EMU03-025-2F-0808-58 up-cut end mill is specially designed for desktop CNC routers such as the Vertigo machines. It provides great cutting performance in a variety of materials such as timber, ply, MDF, plastics, and can even be used on aluminium. The 1/4″ shank size allows you to use most trim routers without adapters.
Product Data
|
|
Brand | ChipX |
Cutter Type | Up-cut End Mill |
Coating | None |
Coolant | None |
Corner Radius | 0in (0mm) |
Unit System | mm |
Workpiece Material | ISO N Non-Ferrous Materials |
Diameter | 3mm |
Flute Length | 8mm |
Length Below Shank | 0in (0mm) |
Flutes | 2 |
Overall Length | 58mm |
Shank Diameter | 0.25in (6.35mm) |
Helix Angle | 45 Degrees |
Vendor: ChipX
Type: Router Bit
Price:
27.60
The ChipX EMU03-025-1F-0808-58 up-cut end mill is specially designed for desktop CNC routers such as the Vertigo machines. It provides great cutting performance in a variety of materials such as timber, ply, MDF, plastics, and can even be used on aluminium. The 1/4″ shank size allows you to use most trim routers without adapters.
Product Data
|
|
Shank Diameter | 0.25in (6.35mm) |
Brand | ChipX |
Coating | None |
Coolant | None |
Corner Radius | 0in (0mm) |
Cutter Type | Up-cut End Mill |
Diameter | 3mm |
Flute Length | 8mm |
Flutes | 1 |
Overall Length | 58mm |
Length Below Shank | 0in (0mm) |
Unit System | mm |
Workpiece Material | ISO N Non-Ferrous Materials |
Vendor: ChipX
Type: Router Bit
Price:
31.63
The ChipX EMD06-025-2F-1226-58 down-cut end mill is specially designed for desktop CNC routers such as the Vertigo machines. It provides great cutting performance in a variety of materials such as timber, plywood and MDF, but could also be used on plastics. The 1/4″ shank size allows you to use most trim routers without adapters.
Product Data | |
Coating | None |
Brand | ChipX |
Shank Diameter | 0.25in (6.35mm) |
Coolant | None |
Corner Radius | 0in (0mm) |
Overall Length | 58mm |
Length Below Shank | 26mm |
Unit System | mm |
Workpiece Material | ISO N Non-Ferrous Materials |
Cutter Type | Down-cut End Mill |
Diameter | 6mm |
Flute Length | 12mm |
Flutes | 2 |
Vendor: ChipX
Type: Router Bit
Price:
27.60
The ChipX EMD06-025-1F-1212-58 down-cut end mill is specially designed for desktop CNC routers such as the Vertigo machines. It provides great cutting performance in a variety of materials such as timber, ply, MDF, plastics, and can even be used on aluminium. The 1/4″ shank size allows you to use most trim routers without adapters.
Product data
|
|
Shank Diameter | 0.25in (6.35mm) |
Brand | ChipX |
Coating | None |
Coolant | None |
Corner Radius | 0in (0mm) |
Flute Length | 12mm |
Overall Length | 58mm |
Length Below Shank | 0in (0mm) |
Unit System | mm |
Workpiece Material | ISO N Non-Ferrous Materials |
Cutter Type | Down-cut End Mill |
Diameter | 6mm |
Flutes | 1 |
]]>
Vendor: Vertigo Technologies
Type:
Price:
27.60
The ChipX CM025-025-2F-90DG-58 chamfer mill is specially designed for desktop CNC routers such as the Vertigo machines. It provides great cutting performance in a variety of materials such as timber, ply, MDF, plastics, and can even be used on aluminium. The 1/4″ shank size allows you to use most trim routers without adapters.
Product data | |
Cutter Type | Chamfer Mill |
Brand | ChipX |
Coating | None |
Coolant | None |
Corner Radius | 0in (0mm) |
Length Below Shank | 0in (0mm) |
Unit System | mm |
Workpiece Material | ISO N Non-Ferrous Materials |
Diameter | 6.35mm |
Shank Diameter | 0.25in (6.35mm) |
Tip Angle | 90° |
Flutes | 2 |
Flute Length | 3.175mm |
Overall Length | 58mm |
Vendor: Vertigo Technologies
Type:
Price:
27.60
The ChipX CM025-025-1F-30DG-58 chamfer mill is specially designed for desktop CNC routers such as the Vertigo machines. It provides great cutting performance in a variety of materials such as timber, ply, MDF, plastics, and can even be used on aluminium. The 1/4″ shank size allows you to use most trim routers without adapters
Product Data | |
Cutter Type | Chamfer Mill |
Brand | ChipX |
Coating | None |
Coolant | None |
Corner Radius | 0in (0mm) |
Length Below Shank | 0in (0mm) |
Unit System | mm |
Workpiece Material | ISO N Non-Ferrous Materials |
Diameter | 6.35mm |
Shank Diameter | 0.25in (6.35mm) |
Tip Angle | 30° |
Flutes | 1 |
Flute Length | 11.8mm |
Overall Length | 58mm |
Vendor: Vertigo Technologies
Type:
Price:
22.77
The ChipX BM06-025-2F-1616-58 ball mill is specially designed for desktop CNC routers such as the Vertigo machines. It provides great cutting performance in a variety of materials such as timber, ply, MDF, plastics, and can even be used on aluminium. The 1/4″ shank size allows you to use most trim routers without adapters
Product data
|
|
Cutter Type | Ball Mill |
Brand | ChipX |
Coating | None |
Coolant | None |
Corner Radius | 0.12in (3mm) |
Overall Length | 58mm |
Length Below Shank | 0in (0mm) |
Unit System | mm |
Workpiece Material | ISO N Non-Ferrous Materials |
Diameter | 6mm |
Flute Length | 16mm |
Flutes | 2 |
Shank Diameter | 0.25in (6.35mm) |
Vendor: ChipX
Type: Router Bit
Price:
19.80
The ChipX BM03-025-2F-0606-58 ball mill is specially designed for desktop CNC routers such as the Vertigo machines. It provides great cutting performance in a variety of materials such as timber, ply, MDF, plastics, and can even be used on aluminium. The 1/4″ shank size allows you to use most trim routers without adapters
Product data | |
Cutter Type | Ball Mill |
Brand | ChipX |
Coating | None |
Coolant | None |
Corner Radius | 0.06in (1.5mm) |
Overall Length | 58mm |
Length Below Shank | 0in (0mm) |
Unit System | mm |
Workpiece Material | ISO N Non-Ferrous Materials |
Diameter | 3mm |
Flute Length | 6mm |
Flutes | 2 |
Shank Diameter | 0.25in (6.35mm) |
Vendor: Vertigo Technologies
Type:
Price:
300.00
The laser is a great upgrade to any Vertigo CNC machine!
Adding the laser to your machine allows you to not only cut with the machine but now laser engrave a great addition to wooden products
The laser is 2.4W suitable cutting paper, thin card, and sheet plastic as well as engraving wood and leather
Included